Drivers Displaylink

DisplayLink devices on Linux still only have experimental support. While some people have had success in using them, it is generally not an easy process and not guaranteed to work. The steps on this page describe the generally most successful methods of using external monitors with DisplayLink.

The table summarises the DisplayLink driver compatibility: V8.0 or later will be installed by Windows Update on Windows 10 Anniversary Update. Running the DisplayLink installer, from the DisplayLink website will also automatically install the appropriate driver for the Windows 10 version you are running.

Also be warned that even over USB 3.0, a DisplayLink monitor may exhibit noticeably more lag than e.g. a DisplayPort monitor, especially when large portions of the screen are being redrawn.

In a corporate environment, it might be desired that the Ethernet driver is not installed to prevent the Ethernet port of the dock being available and a security risk. The Ethernet driver can be uninstalled after deploying DisplayLink software by: Running pnputil to find the inf file for the driver in the Windows driver store. 1.1 This Software is licensed by DisplayLink Corp. (“DisplayLink”) on a non-exclusive, non-transferable basis for use only in conjunction with products which incorporate DisplayLink technology. Use of the Software other than in conjunction with products which incorporate DisplayLink technology is not permitted. The Dell Universal Dock D3000 is a USB docking station made by Displaylink and branded as a Dell. The drivers are on Dell's website and archive of drivers are below. Download the latest drivers, firmware, and software for your HP USB Travel Dock.This is HP’s official website that will help automatically detect and download the correct drivers free of cost for your HP Computing and Printing products for Windows and Mac operating system.

Installation

USB 2.0 DL-1x5, DL-1x0 Devices

The kernel DRM driver for DisplayLink is udl, a rewrite of the original udlfb driver. It allows configuring DisplayLink monitors using Xrandr.

This should work without any configuration changes on linux 4.14.9-1 and later. If you're using an earlier version of that package or have CONFIG_FB_UDL=m set in your kernel config, you need to blacklist the old kernel module, udlfb, which may attempt to load itself first.

USB 3.0 DL-6xxx, DL-5xxx, DL-41xx, DL-3xxx Devices

Install the displaylink^AUR driver. It allows configuring DisplayLink monitors using Xrandr in the same manner as the udl driver.
Enable displaylink.service.
Use the 'modesetting' driver with AccelMethod 'none' and MatchDriver 'evdi'.

Create a file with the following content:

A reboot is required for the setting to be effective. You may need the evdi-git^AUR package.

Setting up X Displays

After that, run:

In the above output, we can see that provider 0 is the system's regular graphics provider (Intel), and provider 1 (modesetting) is the DisplayLink provider. To use the DisplayLink device, connect provider 1 to provider 0:

and xrandr will add a DVI output you can use as normal with xrandr. This is still experimental but supports hotplugging and when works, it is by far the simplest setup. If it works then everything below is unnecessary.

Configuration

These instructions assume that you already have an up and running X server and are simply adding a monitor to your existing setup.

Load the framebuffer device

Before your system will recognize your DisplayLink device, the udl kernel module must be loaded. To do this, run

If your DisplayLink device is connected, it should show some visual indication of this. Although a green screen is the standard indicator of this, other variations have been spotted and are perfectly normal. Most importantly, the output of dmesg should show something like the following, indicating a new DisplayLink device was found:

Furthermore, /dev should contain a new fb device, likely /dev/fb1 if you already had a framebuffer for your primary display.

To automatically load udl at boot, create the file udl.conf in /etc/modules-load.d/ with the following contents:

For more information on loading kernel modules, see Kernel modules#Automatic module loading with systemd.

Configuring X Server

Use xrandr or your Desktop Environment's display setup UI to configure your USB monitors running either the udl or displaylink driver.

xrandr

Once the driver is loaded, the DisplayLink monitor is listed as an output provider:

In the above example, provider 1 is the DisplayLink device, and provider 0 is the default display. Running xrandr --current gives a list of available screens:

If the above does not list the DisplayLink screen, then you will need to offload DisplayLink to the main GPU:

Once the screen is available, refer to Xrandr for info on setting it up. For automating the configuration process, see displaylink.sh.

Enabling DVI output on startup

The DisplayLink provider will not be automatically connected to the main provider in most cases, therefore the DVI output device will not be available. It can be helpful to automatically do this when X starts to facilitate automatic display configuration by the window manager.

Edit your desktop manager's startup configuration and add commands similar to:

For example, the appropriate startup configuration file for SDDM is /usr/share/sddm/scripts/Xsetup.

Avoid placing these commands in ~/.xprofile as this breaks the display configuration of some window managers. Instead these commands should be run prior to any display output or setup.

Note: If you have additional providers, specify the name of the provider instead of using indexes. The name of the DisplayLink device will be modesetting

Switching between displaylink and nvidia/nouveau driver

Currently (displaylink version 1.3.54-1) it is not possible to use displaylink device and nvidia/nouveau driver simultaniously on optimus based laptops.Currently to be able to use displaylink device on intel GPU, you should create config file (see troubleshooting section below). However, with that config file it is not possible to use primusrun. Bumblebee service is running, but it cannot work. Also, laptop's fans are becoming very noisy and laptop's temperature becomes very high. When you want to switch back to activate nvidia driver, comment everything in that file and reboot.

To simplify process of switching, you can installdl-switch^AUR and add an additional menu entry to your bootloader using the kernel parametersystemd.unit=displaylink.target, thus activating displaylink workaround.

To check which driver is used for your discrete video card, run lspci -nnk -s xx:xx.x (replace xx:xx.x with your nvidia gpu pci id).

Troubleshooting

Not working configuration

These are tested on Xfce using Display settings (included in XFCE4 package) and external tool - arandr. XFCE4 Display settings are likely to crash, so ARandR might help.

When you connect display link device via USB to your computer, the computer should show monitors in Display settings. There are few troubleshooting steps that you should try:

Check #Setting up X Displays. If you can find any external monitors recognized, you should try to make them visible by the following commands:

This will make them visible and recognized in Display settings.

Restart displaylink.service.
Re-connect the USB cable.
Check if udl driver is loaded and monitors are connected.

Screen redraw is broken

If you are using udl as your kernel driver and the monitor appears to work, but is only updating where you move the mouse or when windows change in certain places, then you probably have the wrong modeline for your screen. Getting a proper modeline for your screen with a command like

where 1366 and 768 are the horizontal and vertical resolutions for your monitor, and 59.9 is the refresh rate from its specs. To use this, create a new mode with xrandr like follows:

and add it to Xrandr:

Then tell the monitor to use that mode for the DisplayLink monitor, and this should fix the redraw issues. Check the Xrandr page for information on using a different mode.

If this does not solve the problem (or if the correct modeline was already in place because of correct DDC data), it can help to run a compositor.

DisplayLink refresh rate is extremely slow with gnome 3

If once you set up your DisplayLink your entire desktop becomes slow, try setting a 'simpler' background image, such as complete black.

Slow redraw/Unresponsiveness in Google Chrome and Webkit2-based Applications

This is to be associated with bugs in hardware acceleration, which can be tested by running glxgears in the displaylink screen resulting in 1fps. There is currently no complete fix available, but turning off Hardware-Acceleration in affected applications can work as a temporary fix.

This can be done in applications without a hardware-acceleration option by prepending the LIBGL_ALWAYS_SOFTWARE=1 environment variable.

Impossible to activate displaylink's screen

In case you are able to see attached monitor via DisplayLink device in your screen settings, but after you turn it on and apply settings, it becomes deactivated, then try blacklist nouveau module and reboot:

Suspend problem

Displaylink is not working after suspend. Unplug and then plug again displaylink's usb cable to your computer. Monitor that is connected via DisplayLink will remain black. If you have lock screen, login to the system and then picture will appear at that monitor and you will be able to use displaylink as normal.

DisplayLink is not working when usb hot plugged

To be able to use DisplayLink monitors, its usb cable should be attached to laptop during boot time. Otherwise it can behave like they are available and mouse can be moved there, but its picture is frozen, even with correct configuration (see workaround 1). If it was not attached at boot time, attach it and reboot.

DisplayLink driver does not work with Intel GPUs after recent X upgrades

As this support page says, upgrading the X Window Server to a version newer than 1.18.3 will make the system not compatible with DisplayLink by default. This applies to systems using an integrated Intel GPU, or a combination of integrated Intel GPU and a discrete GPU.Until fixes in X Windows System will be released, there are two workarounds:

Workaround 1: Use older intel driver as a fallback

Use the 'intel' driver for the integrated GPU instead of 'modesetting', which is now the default.

Create a file with the following content:

A reboot is required for the setting to be effective.

You may need the evdi-git^AUR package.

Workaround 2: Temporarily disable PageFlip for modesetting

Driver Displaylink

For users that prefer to keep using 'modesetting' driver, disabling page flipping should also help.Create a file with the following content or extend the PageFlip option to an existing configuration file (e.g. 20-evdidevice.conf):

Displays disconnect at random intervals when using the Dell D6000 docking station

Displaylink Drivers Fedora

User's have reported that when using the Dell D6000 docking station, their display(s) may disconnect at random intervals during usage. This will require physically reconnecting the dock in order to reinitialise the displays.

This issue appears to be caused by PulseAudio's module-suspend-on-idle module, which automatically suspends sinks/sources on idle.

Linux Displaylink Drivers

To disable loading of the module-suspend-on-idle module, comment out the following line in the configuration file in use (~/.config/pulse/default.pa or /etc/pulse/default.pa):

Fusionfox353